 |
|
| Badge removal and installation |
| Badge | Location | Part # | MSRP* | Model Year(s) |
 |
Speakers (front door) | 68024539AA | $ 9.00 | 2007-2010 |
 |
Liftgate | 55157095AC | $27.00 | 2007-2008 |
 |
Liftgate (right side) | 68038123AA | $29.95 | 2007-2008 |
 |
Liftgate (right side) | 55372784AA | $39.70 | 2007-2010 |
 |
Liftgate (left side) | 55157091AA superseded by: 55157091AC |
$28.85 | 2005-2010 |
 |
Liftgate (right side) | 55157092AA superseded by: 55157092AB |
$26.10 | 2005 |
 |
Liftgate (right side) | 55079103AA | $37.95 | 2007-2010 |
 |
Liftgate (right side, combo set) (Note: The "5.7L" portion of "5.7L HEMI" badge was deleted on all models built on or after June 29, 2006) |
55157454AA | $44.25 | 2006 |
 |
Hood | 55157088AA superseded by: 55157088AC |
$42.35 | 2005-2010 |
|
Liftgate (center) | 55157089AA superseded by: 55157089AC |
$42.35 | 2005-2010 |
 |
Liftgate (left side) | 55157303AB superseded by: 55157303AF |
$22.35 | 2005-2010 |
 |
Liftgate (left side) | 55157090AA superseded by: 55157090AC |
$28.85 | 2005-2010 |
 |
Door (left side) | 5113554AA | $57.70 | 2008-2010 |
 |
Liftgate | 55157358AA | $37.35 | 2006-2010 |
 |
Door (front) | 55079387AA | $23.50 | 2005, 2007-2009 |
 |
Fender (front) | 55373001AA | $21.75 | 2006 |
 |
Liftgate | 55079385AA | $25.25 | 2008-2010 |
 |
Liftgate (right side, 5-7/8" x 9/16") | 5029893AA superseded by: 5029893AB |
$68.95 | 2006-2010 |
 | Front fender, left side only (heavier and more detailed than 2004 version)
1. All 3.7L 4-wheel drive and 2-wheel drive WK's are NOT Trail Rated. 2. All 4.7L and 5.7L 2-wheel drive WK's are NOT Trail Rated. | 55157317AA superseded by: 55157317AB |
$28.60 | 2005-2010 |
| NOTE: Prices listed are for reference purposes only and may vary by dealer. Prices are current as of November, 2010. Parts are not available from this web site. | ||||
NOTE: Exterior nameplates are attached to body panels with adhesive tape.
1. Apply a length of masking tape on the body, parallel to the top or bottom edge of the nameplate to use as a guide, if necessary. An additional piece of tape can also be placed on the left or right side of the badge for more accurate alignment when reinstalling.
2. If temperature is below 21°C (70°F) warm emblem with a heat lamp or gun. Do not exceed 52°C (120°F) when heating emblem. A hair dryer may also be used.
3. Insert a plastic trim stick or a hard wood wedge behind the emblem to separate the adhesive backing from the body. A short length of fishing line can also be used.
4. Clean adhesive residue from body with MOPAR Super Clean solvent or equivalent.
1. Remove protective cover from adhesive tape on back of emblem.
2. Position emblem properly on body.
3. Press emblem firmly to body with palm of hand.
4. If temperature is below 21°C (70°F) warm emblem with a heat lamp or gun to assure adhesion. Do not exceed 52°C (120°F) when heating emblem.
Exterior badge removal
Installation
wkbible.com website Premier Sponsor
Discount Jeep Parts and Accessories